
2-7/8" x 20" Demineralizing Filter Cartridge
In stock
Not sure about subscribing? Most customers tell us they signed up to stop forgetting — not to save 5%. How long this cartridge lasts depends on the dissolved solids in the water you feed it. Once the resin is spent, the dissolved solids it was holding back return, and spots and residue come with them.
Subscribe and you'll get a fresh cartridge automatically — right when the old one wears out. Cancel, pause, or change your schedule anytime in your account. No phone calls, no obligation, no fees.
A mixed bed deionizing (DI) cartridge that polishes reverse osmosis water to very low dissolved solids for technical uses.
- Reduces dissolved solids (TDS)
- Typical life: set by feed water TDS
- Measures 2-7/8 x 20 in and fits a standard 2.5 x 20 in housing
Replacement cartridge, 2-7/8 x 20 in
Ultra pure water for the jobs that need it
Some uses call for water with almost nothing dissolved in it. This cartridge is filled with mixed bed deionizing resin that takes up both positive and negative ions in one pass. It does its work after reverse osmosis, as a final polish.
- Reduces dissolved solids (TDS)
- Mixed bed DI resin
- Typical life: set by feed water TDS
- Fits a standard 2.5 x 20 in housing

What a fresh cartridge gives you
Very low dissolved solids
Takes up the small amount of dissolved minerals that reverse osmosis leaves behind.
One pass
Mixed bed resin handles positive and negative ions together.
Longer life on RO water
Fed with reverse osmosis water, the resin lasts many times longer than on tap water.
How it works
Mixed bed resin
Cation and anion exchange resins blended in one cartridge.
Ion exchange
Dissolved ions are swapped for hydrogen and hydroxide, which combine into water.
Polishing stage
Best placed after reverse osmosis, where little is left to take up.
What it reduces
Designed to reduce
- Total dissolved solids (TDS)
- Calcium and magnesium
- Sodium and other dissolved metal ions
- Chloride, sulfate, nitrate and bicarbonate
Not designed for
- Chlorine and most organic chemicals
- Sediment
- Bacteria and viruses
This cartridge is made for technical water, such as aquariums, humidifiers, spot-free rinsing and lab use. It is not intended as a drinking water filter.

Find your size
Match the actual size printed on your current cartridge. This one measures 2-7/8 x 20 in and fits a standard 2.5 x 20 in housing, the size used in our compact whole house systems.
| Cartridge size | Fits | Service flow |
|---|---|---|
| 2-7/8 x 9-3/4 in | 2.5 x 10 in housing | 0.5 gpm |
| 2-7/8 x 20 in (this cartridge) | 2.5 x 20 in housing | 2.5 gpm |

Specifications
| Part number | CQE-RC-04023 |
|---|---|
| Cartridge size | 2-7/8 x 20 in (actual) |
| Fits | Standard 2.5 x 20 in housing |
| Service flow | 2.5 gpm |
| Typical life | Set by the dissolved solids in the feed water |
| Media | Mixed bed deionizing resin |
| Recommended feed | Reverse osmosis water |
| Operating pressure | 20 to 125 psi |
| Water temperature | 40 to 85°F |
| Made in | USA |
How to replace it
A few minutes, with the wrench that came with your system.
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Timing and care tips are in the Replacement Schedule tab. Questions about fit? Contact us.
| SKU | CQE-RC-04023 |
|---|---|
| Country of Manufacture | United States |
| On Sale | No |
When to replace it
It depends on the dissolved solids in the feed water. The lower the feed TDS, the longer it lasts. Check the output with a TDS or resistivity meter and replace the cartridge when the reading no longer meets your needs.
- Replace it when a TDS or resistivity meter shows the output no longer meets your needs.
How to replace it
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Between changes
- Keep your reverse osmosis pre-filters and membrane current. A tired RO stage sends more dissolved solids to the DI cartridge and shortens its life.
- Write the install date on the cartridge label or in your calendar so the next change is easy to time.
Never run late on a change. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery.
Questions about timing? Contact us.
Demineralizing (DI) Filter Cartridge FAQ
What is a mixed bed DI cartridge?
It blends cation and anion exchange resins, so it takes up positive and negative dissolved ions in one pass.
Should I use it on tap water or RO water?
It is made to polish reverse osmosis water. On tap water the resin is used up many times faster.
Is DI water for drinking?
This cartridge is made for technical water, not as a drinking water filter.
How often should I replace the DI cartridge?
It depends on the dissolved solids in the feed water. The lower the feed TDS, the longer it lasts. Check the output with a TDS or resistivity meter and replace the cartridge when the reading no longer meets your needs.
Which size do I need?
Match the actual size printed on your current cartridge. This cartridge measures 2-7/8 x 20 in and fits a standard 2.5 x 20 in housing. Housings are often named by nominal size, which is slightly larger than the cartridge itself.
How do I replace it?
Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath. Unscrew the housing with the housing wrench and lift out the used cartridge. Fit the new cartridge, turn the water on slowly, check for leaks and flush before first use. Full steps are in the Replacement Schedule tab.
Can I have replacements delivered automatically?
Yes. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery. You can pause, change or cancel anytime in your account.
