
2-7/8" x 9-3/4" 5-Micron Sediment Reusable Pleated Cartridge
In stock
Not sure about subscribing? Most customers tell us they signed up to stop forgetting — not to save 5%. Your cartridge is good for 12 to 24 months. After that, the sand, silt and rust it was catching start getting through, and the cartridges behind it clog sooner.
Subscribe and you'll get a fresh cartridge automatically — right when the old one wears out. Cancel, pause, or change your schedule anytime in your account. No phone calls, no obligation, no fees.
A 5 micron pleated cartridge that catches sand, silt, dirt and rust before they reach the finer stages of your system.
- Catches sand, silt, dirt and rust
- Typical life: 12 to 24 months
- Measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing
Replacement cartridge, 2-7/8 x 9-3/4 in
Clear water starts with catching the grit
Sand, silt and rust do more than cloud your water. They clog the finer, more costly stages that come after. This 5 micron pleated cartridge catches them first, so the rest of your system can do its work.
- Catches sand, silt, dirt and rust
- Pleated for high dirt capacity
- Typical life: 12 to 24 months
- Fits a standard 2.5 x 10 in housing

What a fresh cartridge gives you
Clearer water
Reduces the sand, silt, dirt and rust particles that cloud water and settle in fixtures.
Longer life for other stages
Keeps sediment off the carbon, SMART and membrane stages that follow.
Strong, steady flow
Pleats multiply the surface area, so the cartridge holds more dirt before flow drops.
How it works
Pleated media
Folded filter media gives a large surface for catching particles.
5 micron rating
Holds back suspended particles down to 5 microns.
Sturdy build
A polypropylene core with end caps sealed to the media.
What it reduces
Designed to reduce
- Sand and silt
- Dirt
- Rust particles
- Other suspended particles down to 5 microns
Not designed for
- Chlorine and chemicals
- Dissolved metals such as iron and lead
- Fluoride and nitrate
- Water hardness
- Bacteria and viruses
It filters suspended particles only. Anything dissolved in the water passes through and is handled by the stages after it.

Find your size
Match the actual size printed on your current cartridge. This one measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing, the size used in our countertop, under sink and refrigerator systems.
| Cartridge size | Fits | Service flow |
|---|---|---|
| 2-7/8 x 9-3/4 in (this cartridge) | 2.5 x 10 in housing | 0.5 gpm |
| 2-7/8 x 20 in | 2.5 x 20 in housing | 2.5 gpm |
| 4-5/8 x 9-3/4 in | 10 in Big Blue housing | 3 gpm |
| 4-5/8 x 20 in | 20 in Big Blue housing | 6 gpm |

Specifications
| Part number | CQE-RC-04001 |
|---|---|
| Cartridge size | 2-7/8 x 9-3/4 in (actual) |
| Fits | Standard 2.5 x 10 in housing |
| Service flow | 0.5 gpm |
| Typical life | 12 to 24 months |
| Media | Pleated sediment media on a polypropylene core |
| Micron rating | 5 micron |
| Water temperature | 40 to 145°F |
| Made in | USA |
How to replace it
A few minutes, with the wrench that came with your system.
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Timing and care tips are in the Replacement Schedule tab. Questions about fit? Contact us.
| SKU | CQE-RC-04001 |
|---|---|
| Country of Manufacture | United States |
| On Sale | No |
When to replace it
Typically every 12 to 24 months. Replace it sooner if the taste, odor, flow or pressure of your water changes. Actual life depends on your water quality and how much water you use.
- Replace it sooner if the flow or pressure drops.
- Replace it sooner if the pleats look heavily loaded with dirt.
How to replace it
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Between changes
- Keep a spare on the shelf. Sediment loads can jump after plumbing work, a water main break or heavy rain on a well.
- Change it together with the stages after it, so a fresh sediment cartridge protects fresh media.
- Write the install date on the cartridge label or in your calendar so the next change is easy to time.
Never run late on a change. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery.
Questions about timing? Contact us.
5 Micron Pleated Sediment Filter Cartridge FAQ
Why choose a pleated sediment filter?
The pleats give the media a large surface area, which raises its dirt-holding capacity and keeps flow strong for longer.
Does a sediment filter treat dissolved contaminants?
No. It filters suspended particles only. Chlorine, dissolved metals, nitrate and fluoride need a carbon, SMART or specialty stage.
Why did my sediment filter clog early?
Your water is carrying more sediment than usual. That is common on well water, after plumbing work or after a water main break. Replace the cartridge and check it more often.
How often should I replace the sediment cartridge?
Typically every 12 to 24 months. Replace it sooner if the taste, odor, flow or pressure of your water changes. Actual life depends on your water quality and how much water you use.
Which size do I need?
Match the actual size printed on your current cartridge. This cartridge measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing. Housings are often named by nominal size, which is slightly larger than the cartridge itself.
How do I replace it?
Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath. Unscrew the housing with the housing wrench and lift out the used cartridge. Fit the new cartridge, turn the water on slowly, check for leaks and flush before first use. Full steps are in the Replacement Schedule tab.
Can I have replacements delivered automatically?
Yes. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery. You can pause, change or cancel anytime in your account.
