
2-7/8" x 9-3/4" Arsenic/Multi Filter Cartridge
In stock
Not sure about subscribing? Most customers tell us they signed up to stop forgetting — not to save 5%. This cartridge is rated by the gallon, so its life depends on how much water you use. Once the media is spent, the arsenic it was filtering starts coming back through, and arsenic has no taste to warn you.
Subscribe and you'll get a fresh cartridge automatically — right when the old one wears out. Cancel, pause, or change your schedule anytime in your account. No phone calls, no obligation, no fees.
One cartridge that pairs iron-based arsenic media with SMART carbon and redox media for chlorine taste and odor.
- Reduces arsenic and chlorine
- Rated for 500 gallons
- Typical life: set by rated gallons
- Measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing
Replacement cartridge, 2-7/8 x 9-3/4 in
Arsenic and chlorine, handled by one cartridge
This cartridge pairs iron-based arsenic media with SMART carbon and redox media. One stage reduces arsenic, and the other takes care of chlorine taste and odor and low levels of iron and hydrogen sulfide.
- Reduces arsenic and chlorine
- Rated for 500 gallons
- Typical life: set by rated gallons
- Fits a standard 2.5 x 10 in housing

What a fresh cartridge gives you
Two treatments, one cartridge
Iron-based arsenic media, plus SMART carbon and redox media.
Both forms of arsenic
Designed for arsenic V and arsenic III.
Better taste
The carbon and redox media reduce chlorine and its taste and odor.
How it works
Iron-based arsenic media
Arsenic binds to the iron hydroxide surface and stays there.
Activated carbon
Adsorbs chlorine, taste, odor and organic chemicals.
Copper-zinc redox media
Adds chlorine reduction and helps with low levels of iron and hydrogen sulfide.
What it reduces
Designed to reduce
- Arsenic V and arsenic III
- Chlorine taste and odor
- Ferrous iron and hydrogen sulfide at low levels
- Some heavy metals
- Some dissolved organic chemicals
Not designed for
- Bacteria and viruses
- Fluoride
- Nitrate
- Water hardness
- Total dissolved solids (TDS)
Start with an arsenic test. For a dedicated arsenic stage with more capacity, see the Arsenic cartridge.

Find your size
Match the actual size printed on your current cartridge. This one measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing, the size used in our countertop, under sink and refrigerator systems.
| Cartridge size | Fits | Service flow |
|---|---|---|
| 2-7/8 x 9-3/4 in (this cartridge) | 2.5 x 10 in housing | 0.5 gpm |

Specifications
| Part number | CQE-RC-04051 |
|---|---|
| Cartridge size | 2-7/8 x 9-3/4 in (actual) |
| Fits | Standard 2.5 x 10 in housing |
| Service flow | 0.5 gpm |
| Rated capacity | 500 gallons (at under 100 ppm hardness) |
| Typical life | Set by the rated gallons and your water use |
| Media | Iron hydroxide arsenic media, activated carbon, copper-zinc redox alloys |
| Operating pressure | 20 to 60 psi |
| Water temperature | 40 to 90°F |
| Made in | USA |
How to replace it
A few minutes, with the wrench that came with your system.
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Timing and care tips are in the Replacement Schedule tab. Questions about fit? Contact us.
| SKU | CQE-RC-04051 |
|---|---|
| Country of Manufacture | United States |
| On Sale | No |
When to replace it
Plan the change from the rated gallons for this size and your daily water use, then confirm with an arsenic test of the filtered water. Because it has no taste or smell, a water test is the reliable way to know when the media is spent.
- Replace it when the rated gallons are used.
- Replace it when an arsenic test of the filtered water shows the level rising.
How to replace it
- Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath.
- Unscrew the housing with the housing wrench and lift out the used cartridge.
- Wash the housing with mild soap and water and rinse it well.
- Check that the O-ring is clean and fully seated in its groove.
- Unwrap the new cartridge and set it in, centered and fully seated. If one end is marked "This End Up, Toward Cap", that end faces the cap.
- Screw the housing back on by hand, then snug it with the wrench. Do not overtighten.
- Turn the water on slowly, check for leaks, then flush the new cartridge before first use.
Between changes
- Test the filtered water for arsenic on a regular schedule.
- Flush a new cartridge before first use.
- Write the install date on the cartridge label or in your calendar so the next change is easy to time.
Never run late on a change. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery.
Questions about timing? Contact us.
Arsenic/Multi SMART Filter Cartridge FAQ
What does the Arsenic/Multi cartridge add?
Activated carbon and copper-zinc redox media, which reduce chlorine taste and odor and low levels of iron and hydrogen sulfide.
Does it reduce both arsenic III and arsenic V?
The media is designed for both forms. Arsenic V is captured most readily.
How do I know when the cartridge is spent?
Test the filtered water. Replace the cartridge when arsenic starts to rise or the rated gallons are used, whichever comes first.
How often should I replace the arsenic cartridge?
Plan the change from the rated gallons for this size and your daily water use, then confirm with an arsenic test of the filtered water. Because it has no taste or smell, a water test is the reliable way to know when the media is spent.
Which size do I need?
Match the actual size printed on your current cartridge. This cartridge measures 2-7/8 x 9-3/4 in and fits a standard 2.5 x 10 in housing. Housings are often named by nominal size, which is slightly larger than the cartridge itself.
How do I replace it?
Turn off the water supply to the filter and release the pressure as your system manual directs. Place a towel or drip pan underneath. Unscrew the housing with the housing wrench and lift out the used cartridge. Fit the new cartridge, turn the water on slowly, check for leaks and flush before first use. Full steps are in the Replacement Schedule tab.
Can I have replacements delivered automatically?
Yes. Choose Subscribe and save when you order and a fresh cartridge arrives on the schedule you set, with 5% off each delivery. You can pause, change or cancel anytime in your account.
