
Haven 800 GPD Under Sink Tankless Reverse Osmosis System
In stock
A comprehensive under sink reverse osmosis system that reduces up to 99% of a wide range of contaminants and makes up to 800 gallons per day, with no tank.

Haven is an under sink tankless reverse osmosis system that makes purified water as you pour, from one quiet unit that looks after itself.
A haven is the place where you stop worrying. That is the idea behind this one: a tankless RO system made so that water is the one thing at home you never have to think about.

Designed with intention.
Every line has a reason. Nothing is there for show.

Easy from day one.
Two simple cartridges. Press, pull, then push the new one in. Done in seconds, no tools.

Fresh, never stored.
There is no tank, so no water sits for days. Every glass is made the moment you pour it.

Soft curves. A glass front.
Rounded corners and a glass face, finished with care even where no one looks.
How it works
Haven sits in the cabinet under your kitchen sink and feeds a drinking faucet of its own. With no storage tank to fill, it makes water only when you open the faucet, at up to 800 gallons per day.
Two cartridges do the work. The PPC pre-filter's three layers take out sediment, chlorine and chloramine. The reverse osmosis membrane, rated at 0.0001 micron, then holds back dissolved solids, lead, arsenic, fluoride and PFAS, and rinses them to the drain.

PPC composite pre-filter: 5 micron polypropylene, 5 micron coconut shell carbon block and 1 micron polypropylene.

800 GPD reverse osmosis membrane: thin film composite, 0.0001 micron.
What Haven reduces
- Fluoride: up to 96%
- Arsenic: up to 96%
- Chromium: up to 98%
- Lead: up to 98%
- Dissolved solids: up to 99%
- PFAS: up to 99%
- Microplastics: up to 99%
Haven reduces more than 80 contaminants in all. Figures are based on Crystal Quest internal testing and field performance.

In your home
Lights on the front tell you when a cartridge is due, about every 12 to 18 months for the pre-filter and every 3 to 4 years for the membrane, and each one pushes in by hand. Haven rinses its own membrane, and a sensor on its base shuts the system off if it detects a leak.
It arrives with both cartridges in place, the drinking faucet, a feed valve, tubing and fittings. The unit is 16 in deep, 6 in wide and 13.5 in high.
- Out of sight under your sink, and quiet while it works.
- BPA-free and lead-free materials, everywhere the water touches.

Thoughtful where it matters

Water the way it was intended.
Clean and crisp for the glass, the coffee and the cooking. And far less scale in your kettle.

Know when it's time to swap.
A light tells you when a cartridge is due, about every 12 to 18 months for the pre-filter.

Fast filtration on demand. No waiting.
An 8 oz glass in about 7 seconds. A 34 oz pitcher in about 30. A 68 oz pot in about a minute.
Efficiency and size

About 1 gallon to the drain for every 3 gallons of purified water.

16 in deep, 6 in wide and 13.5 in high.

Before you order
The Installation and requirements section below lists what Haven needs under your sink. Coconut allergy? The pre-filter's carbon block is made from coconut shell. Please contact us before you buy.
Parts included
- Haven tankless RO unit
- PPC composite pre-filter (CQE-PR-8000), installed
- 800 GPD RO membrane (CQE-RO-8000), installed
- Drinking faucet with LED filter life indicator
- Three-way feed valve
- Drain clamp
- Power adapter
- Faucet power cable
- Inlet, drinking water and drain tubing
- Fittings and locking clips
- Owner's manual

Specifications
| Model | Haven, CQE-ROS-8000 |
|---|---|
| Format | Tankless under sink reverse osmosis drinking water system |
| Rated production | 800 GPD (gallons per day) at standard test conditions |
| Faucet flow | 0.53 GPM (2.0 L/min) |
| Filtration | Two push-in cartridges: a three-layer composite pre-filter, then a thin film composite (TFC) RO membrane |
| Filter media | 5 micron polypropylene, 5 micron coconut shell carbon block and 1 micron polypropylene (PPC pre-filter); thin film composite (TFC) reverse osmosis membrane, 0.0001 micron |
| Pre-filter | PPC composite pre-filter, CQE-PR-8000: 5 micron polypropylene, 5 micron coconut shell carbon block, 1 micron polypropylene; rated for 10,000 gallons |
| RO membrane | 800 GPD TFC reverse osmosis membrane, 0.0001 micron, CQE-RO-8000 |
| Salt rejection | 95 to 99% of total dissolved solids |
| Rejection, metals and fluoride | Lead, cadmium and chromium 96 to 98%; selenium 97%; arsenic and fluoride 94 to 96% (based on Crystal Quest internal testing and field performance) |
| Drain ratio | 3:1, about 1 gallon to drain for every 3 gallons of purified water |
| Storage tank | None; water is made on demand |
| Booster pump | Built in |
| Flushing | Automatic membrane flush, plus a manual flush of about 30 seconds (SELECT / FLUSH) |
| Indicators | WORK, PPC, RO and FAULT lights on the front panel |
| Leak protection | Built-in leak sensor on the bottom of the unit; shuts the system off if it detects a leak |
| Faucet | Dedicated drinking faucet with LED Filter Life Indicator, powered from the unit |
| Feed water | Treated municipal (city) cold tap water |
| Water pressure | 14.5 to 58 psi (0.1 to 0.4 MPa) |
| Water temperature | 41 to 100°F (5 to 38°C) |
| Room temperature | 39 to 104°F (4 to 40°C) |
| Electrical | 110 V, 60 Hz, 95 W |
| Connections | 3/8 in inlet tubing; 1/4 in drinking water and drain tubing; quick-connect fittings with locking clips |
| Tubing included | About 5 ft (1.5 m) each of inlet, drinking water and drain tubing |
| Replacement interval, PPC pre-filter | 12 to 18 months (rated for 10,000 gallons), or sooner when the PPC light comes on |
| Replacement interval, RO membrane | 36 to 48 months, or sooner when the RO light comes on |
| Unit size (depth x width x height) | 16 x 6 x 13.5 in |
| Net weight | 20.94 lb (9.5 kg) |
| Shipping weight | 25.79 lb (11.7 kg) |
| Shipping box | 20.67 x 9.25 x 21.06 in, 1 unit per box |
| Housing | White ABS with a glass front cover |
| Mounting | Stands on a level surface in the sink cabinet |
| Warranty | One year limited on the system; replacement filters and RO membranes are not covered |
Production is rated at standard conditions. Actual output and filter life vary with water pressure, temperature and incoming water quality.
Installation and requirements
Check these before you order
- Space: a level spot in the sink cabinet for a unit 16 in deep, 6 in wide and 13.5 in high. The filters change from the front, so keep the front of the unit reachable.
- Cold water: a shutoff valve (angle stop) on the cold line, where the included three-way feed valve fits.
- Power: an outlet (110 V, 60 Hz) within reach of the unit's back panel. Haven is rated at 95 W.
- Drain: a drain point within reach of the back panel. The drain line connects to the sink drain pipe above the trap; follow local plumbing code.
- Faucet: a spare sink hole, or room to drill one near the sink edge.
- Water: treated city (municipal) cold water at 41 to 100°F and 14.5 to 58 psi. Above 58 psi, fit a pressure-reducing valve; below 14.5 psi, add a booster pump. Neither is included.
- Room: 39 to 104°F, away from freezing temperatures and direct sun.
Tools to have ready (not included)
- Adjustable wrench
- Screwdriver
- Drill and bit (only if you need a new faucet hole)
- Tube or pipe cutter
- PTFE (Teflon) thread tape
Installation, step by step
- Turn off the cold water at the angle stop and open a faucet to release the pressure. Keep the unit unplugged until the last step.
- Fit the three-way feed valve on the cold water angle stop, with PTFE tape on the threads, and check it for leaks.
- Mount the drinking faucet in a spare sink hole, or drill one near the sink edge. Seat it with the stainless plate, rubber mats, lock washer and fixed nut so it swivels freely.
- For each tube: remove the C-clip, cut the tube end square, push it fully into the fitting, refit the clip, then tug gently to check it is locked.
- Connect each line to its labeled port on the back of the unit: Inlet Water, Drinking Faucet and Drain, then Power and Faucet Power.
- Connect the power adapter and the faucet cable, open the feed valve slowly, restore power and check every joint for leaks.
First start
- Let Haven run and discard the water it makes for the first 1 to 2 hours. This rinses the new filters and prepares the membrane.
- The WORK light flashes while Haven makes water. Press and hold SELECT / FLUSH for an extra rinse of about 30 seconds at any time.
- After a long time unused, run it for about 20 minutes, dispensing and discarding twice, then use it as normal.
Good to know
- Output slows in colder weather as the water temperature drops. That is normal.
- Installation is not included. Professional installation is recommended, and the installation must meet local plumbing codes. Questions before or during the install? Contact us.
Warranty
Crystal Quest warrants the Haven system under its one year limited warranty: one year from the date of purchase, against defects in materials and workmanship, when it is used as the owner's manual directs. Replacement filters and reverse osmosis membranes are not covered. The warranty applies when the system is properly installed by a qualified, licensed plumber.
| SKU | CQE-ROS-8000 |
|---|---|
| Dimensions | 16"D x 6"W x 13.5"H |
| On Sale | No |
Two filters. A light for each.
- PPC composite pre-filter (CQE-PR-8000): every 12 to 18 months, rated for 10,000 gallons. It reduces chlorine, chloramine, VOCs, sediment, and taste and odor, and keeps chlorine away from the membrane.
- RO membrane (CQE-RO-8000): every 36 to 48 months (3 to 4 years).
- Actual life depends on your water quality and use. The PPC and RO lights on the front panel show when each filter is due.
Changing a filter, no tools
- Close the feed valve and open the drinking faucet to release the pressure.
- Open the front cover, press the release beside the filter's bay (PPC on top, RO below) and take the old cartridge out.
- Push the new cartridge in until it seats.
- Close the cover, open the feed valve and check for leaks.
- Reset the matching light with the RESET button.
- Run a flush of about 30 seconds before you drink the water.
Everyday care
- Haven rinses its membrane automatically. Press and hold SELECT / FLUSH for an extra rinse of about 30 seconds whenever you like.
- Keep the unit level, away from freezing temperatures and direct sun.
- If the FAULT light comes on, close the feed valve, disconnect power and contact us.
- Use only genuine Crystal Quest Haven filters.
What is a tankless RO system and how does it work?
A tankless reverse osmosis system makes purified water as you pour instead of storing it in a tank. In Haven, a pre-filter takes out sediment and chlorine, a booster pump raises the pressure, and a 0.0001 micron membrane holds back dissolved solids, metals and chemicals, which are rinsed to the drain.
Tank vs tankless RO system: which is better?
Neither is better for every home. Tankless wins on space, water efficiency and continuous flow; a tank wins on lower upfront cost and working without electricity. Haven is the tankless kind, so there is no tank to fill, wait on or clean, and it needs a power outlet under the sink.
Does Haven take minerals out of the water?
Yes. Reverse osmosis reduces dissolved solids, and the minerals in tap water are part of them. Haven does not add minerals back. If you want minerals in your drinking water, add an inline alkalizer cartridge.
Can Haven feed a refrigerator or ice maker?
Yes, Haven can also feed a refrigerator or ice maker. Contact us and we will help you plan the connection.
Can I use Haven on well water?
Haven is built for treated city water. Haven is not a disinfection system; use it only on microbiologically safe water; add inline UV. If you are on a private well, contact us with your latest water test before you buy.
Is Haven certified?
Haven does not carry a product certification. Crystal Quest runs its work on an ISO 9001 quality management system, and the reduction figures on this page are based on Crystal Quest internal testing and field performance.
